Sales (850) 570-2824
Support (801) 432-0606
Fax (877) 309-1951


** Do you have a question? Send us an Email and we'll be happy to respond.**

******************************************************************************************************************************************************
Q: How can I determine the number of plates in each HydroTube model?

A: The HydroTube model # legend: HT##-####

 

Example: HT5-804

HT = HydroTube,

5, 10, or 50 = # of Stacks,  

6,8, or 10 = Diameter of the HydroTube,

04,06,08,10,12,14,16,18, or 20 = # of plates per stack.

 

To determine the # of plates in any model HydroTube, multiply the # of Stacks by the # of plates per stack.

Therefore. the HT5-804 is 8" in diameter and has 20 plates (5x4). The HT50-820 is 8" in diameter and has 1000 plates (50x20).


******************************************************************************************************************************************************

Q. Is the HydroTube made with high quality materials?
A:
HydroTube is made with the highest quality, precision cut, materials that have been tested and re-tested to ensure durability and reliability.

Gaskets and other integral components are made from the very highest quality and strength commercial grade Neoprene specifically selected after years of environmental testing to withstand extended use under a wide variety of temperature conditions.

Gas separation mebranes are made of a semi-permeable, ultra-micro porous plastic material that provides excellent gas separation and will last the lifetime of the cell when the cell is installed and operated per Hybrid Hydrotech's instructions.

All plates are made from 316L stainless steel that will not corrode. For customers requiring efficiency levels higher than 70%, Nickel/Nickel alloy plates are available upon request.

Hybrid Hydrotech, LLC’s mission is to design and manufacture the very best electrolytic Hydrogen gas generators on the market. Our commitment is to continue to research, refine, and implement, those advancements in HydroTube technology.

******************************************************************************************************************************************************

Q:
What is the recommended DC Voltage and Amperage that the HydroTube (P) should operate at?
A: Hybrid Hydrotech recommends that the HydroTube (P) be operated at 295 watts/liter/minute of H2 gas.

The HydroTube (P) recommended wattage can be achieved in any combination of voltage, within the voltage range of  model series being operated, (12-14 volts, 24-28 volts, or 120 volts) and an Amperage that equals 295 watts/liter/minute of H2 gas.

For Example: Model# HT5-804 (P) is designed to operate between 12v -14v DC. it is designed to generate 1.7 lpm of H2 gas at Hybrid Hydrotech's recommended power consumption of 295 watts/liter/minute of H2.  The general formula to determine the recommended operating amperage at any voltage within 12v - 14v is: Model # lpm of H2 * 295 / voltage = Operating Amps

At 12 volts the Amperage would be: 1.7 lpm * 295 watts / 12 volts = 41.8 amps
At 14 volts the Amperage would be: 1.7 lpm * 295 watts / 14 volts = 35.8 amps
At 13.5 volts the Amperage would be: 1.7 lpm * 295 watts / 13.5 volts = 37.1 amps

To determine the kWh that a specific Model HydroTube will consume over an hour, multiply the Model # H2 lpm as listed in the Price and Performance section of our web * 0.295 kWh. The general formula is:  Model # lpm of H2 * 0.295 = Energy consumption per hour in kWh

For Example: The HT5-804 (P) produces 1.7 lpm of H2 gas when operated at Hybrid Hydrotech's recommended wattage of 295 watts/liter/minute .Therefore the total kWh consumed over 60 minutes will be: 1.7 * 0.295 = 0.5 kWh of electricity.

A kWh calculator is available at: http://www.rapidtables.com/calc/electric/watt-to-kwh-calculator.htm

******************************************************************************************************************************************************

Q:
What is the normal gas output pressure of a HydroTube?
A: This will vary depending on the amount of gas being generated and the inner diameter of the gas discharge outlet. The larger the gas volume and the smaller the inner diameter of the discharge outlet, the higher the output pressure. Conversly, the larger the inner diameter of the discharge outlet and the lower the gas volume, the lower the gas output pressure. Each customer's operation will determinethe actual gas output presure, however the HydroTube is intended to operate between 2 psi to 15 psi depending on the model.

******************************************************************************************************************************************************

Q: What is the maximum internal pressure HydroTube will sustain?
A: Hybrid Hydrotech has not tested the maximum pressure limits of what the HydroTube can withstand. The cell is not intended to be pressurized beyond the pressure developed within the cell during the generation of gas. If a user permits the cell or tanks to build up pressure beyond what is normally created during the generation of on-demand gas, Hybrid Hydrotech considers this approach to compressing and/or storage of gas as unauthorized and can be dangerous.

*****************************************************************************************************************************************************

Q: How does Hydrogen Compare to Propane:

A: Click Here

 

******************************************************************************************************************************************************

Q: How does Hydrogen stack up against other combustible fuels?
A: Click Here

******************************************************************************************************************************************************

Q: What are the impediments to improved fuel mileage using HHO?
A: Click Here

******************************************************************************************************************************************************

Q: Why should a water bubbler be used to cleanse H2 and O2 gas of trace amounts of KOH particles?
A: Depending upon the output temperature of the gas, very small amounts of KOH can cling to the moisure content in the H2 and O2 gas produced by the HydroTube. This is normal. We recommend that it be removed from the gas stream before use. KOH is a very caustic chemical and can pit, or in high concentrations corrode, certain metals especially aliminum.

For a recent study to show the benefitial results of H2 water purification Click Here

******************************************************************************************************************************************************

Q: Where can I get a copy of the HydroTube Installation Manual?
A: Click Here

*****************************************************************************************************************************************************